The power station requires no flammable fuel to run. We never had down time waiting for the batteries to charge.Īnother benefit of the portable power station is that it has a built-in inverter to power your corded power tools. This was a huge advantage when we were on a recent deck project, fully cordless and running six DEWALT cordless tools on 20V and 60V FLEXVOLT throughout the day. The first one is the ability to charge up to four batteries at once. The portable power station offers a multitude of great benefits. I had plenty of power to run the variable speed multi-tool for approximately 30 minutes and never felt the tool bog down due to lack of power provided from the Portable Power Station. I plugged in a 12 gauge 25 foot extension cord, ran the cord out to the multi tool, and started my repair work. Just install your four DEWALT batteries and press the power button to turn the unit on and provide outgoing power. Again, there were no outdoor outlets near the work area. The second project consisted of running a corded multi-tool to cut away rotted soffit. The power station never hesitated and gave us the power we required for approximately 2 hours, the entire length of the job. Each tool was plugged into the unit to give power one at a time. This project required a corded 25lb rotary hammer and a corded impact wrench. The first job the DEWALT Portable Power Station was put to work on had no outdoor electrical outlets. DEWALT Portable Power Station Field Performance The DEWALT Portable Power Station should not be used with any medical or life saving devices. You can replace that one battery, turn unit back on, and continue working on your project. When one battery reaches it’s low charge, the unit will shut off, beep ten times and the LED will flash yellow below the battery for 30 seconds. The Power Station LED lights will flash in a left to right fashion when one or more batteries are getting low in charge. If the unit is getting low on battery power it will beep 2 times every 30 seconds to let you know your time is limited. When the unit goes into fault mode, it will beep 10 times, the LED on the top front will flash and the unit will shut off. So it’s possible to run the power station with a mixture of both 20V and 60V battery packs, obviously the most powerful situation would be running the unit on four 60V FLEXVOLT packs for maximum power output and run time. The system is sold as a bare unit or with three (3) – 4.0 Ah MAX batteries and one (1) – 60V FLEXVOLT battery. Also, DEWALT recommends that a minimum 3.0 Ah battery packs be used in this mode. In power out mode, the unit is only as strong as its weakest link. The unit does have a built in cooling fan to assist with cooling the unit and batteries. When using the DCB1800M3T1 for high demand applications, the batteries can get warm, so it is recommended to remove them from the unit and place the batteries in a cool area. If you get a solid yellow light with a blinking red, that indicates the temperature of the battery is too hot or too cold. Solid red is fully charged and slow blinking red is charging. The Portable Power Station features LED indicator lights that let users know the status of the battery packs. Multi-port chargers are very convenient when you’re running multiple tools reducing the need to set up or carry four independent chargers. The parallel charging system will allow you to charge all four of your batteries at the same time. The DCB1800M3T1 will charge and run on both 20V MAX and 60V MAX FLEXVOLT batteries. The charging system allows you to charge between one and up to four batteries. The inverter delivers 1800W of continuous power and 3600W of peak AC power when four 20V MAX batteries are used. The DEWALT Portable Power Station is both a battery charger, and a power supply device that converts the DC battery pack charges into an AC current. Indicator lights – Inverter & charger, operation & fault, low batteryĭEWALT Portable Power Station Charging System.Charging time 2 hours, 4.0 AH batteries.Charging connection is a male plug 120V.1800 Watts of continuous portable power.The Portable Power Station allows you go cordless, with a corded power tool.ĭEWALT Portable Power Station Features & Specifications DEWALT’s newest addition, the Portable Power Station, aims to give users power anywhere, and the ability to run corded power tools without the need for traditional 120V AC power. FLEXVOLT gives you the power of your corded power tools without the cord. This new line of cordless power tools and accessories is providing us with the first in the industry cordless job site table saw and 12 inch miter saw. Power source: 20V Max/Flex Volt BatteriesĭEWALT burned their competition this summer when they launched FLEXVOLT at their 2016 media event.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |